欢迎访问润滑与密封官方网站!

咨询热线:020-32385313 32385312 RSS EMAIL-ALERT
钼铁合金对铜基摩擦材料性能影响
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

辽宁省教育厅科学研究项目(L2013188);中国铁路总公司重点科技计划(2013J011-E)


Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用粉末冶金技术制备铜基摩擦材料,利用销盘式摩擦试验机,在摩擦速度为3.1~47.1 m/s的范围内,研究钼铁合金对铜基粉末冶金摩擦材料性能影响。实验结果表明:材料添加钼铁合金,提高了摩擦因数和耐磨性,并且影响程度与摩擦速度有关。低速摩擦时,钼铁合金含量增加,摩擦因数和磨损率变化不大,这是由于钼铁合金剥落的概率相应增加,摩擦表面微凸体的数量没有明显改变;高速摩擦条件下,表面硬质微凸体增加和连续致密的第三体降低表面粗糙度的综合的作用使得摩擦因数变化不大。钼铁合金含量增加,增强基体抗软化能力,降低犁削程度,发挥良好耐磨性。

    Abstract:

    Preparing copper base friction materials with powder metallurgy technology.With pin disc friction tester,in the friction velocity for the range of 3.14 - 47.1 m/s,We did a research about the effects of molybdenum alloy on performance of copper base powder metallurgy friction materials.The experimental results show that:add molybdenum alloy material,improve the coefficient of friction and wear resistance,and impact related to the friction velocity.Low speed,with Molybdenum alloy content increases,the friction coefficient and wear rate is a little change.This is because the ferromolybdenum peeling probability increase,the number of micro convex body of friction surface have no obvious change;High speed,the comprehensive effect of hard surface micro convex body increased and the continuous density third body reduced the surface roughness result in friction coefficient changed little.so increased molybdenum alloy content can enhance the softening resistance ability of the substrate,reduce the degree of the plough cutand express a good wear resistance.

    参考文献
    相似文献
    引证文献
引用本文

张娟娟,高 飞,韩晓明,藤颍丽.钼铁合金对铜基摩擦材料性能影响[J].润滑与密封,2015,40(11):60-64.
.[J]. Lubrication Engineering,2015,40(11):60-64.

复制
分享
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期: 2016-01-08
  • 出版日期: